How To Test & Repair A Halogen Downlight
Shock your friends with this post.
Key Takeaways
- Work by elimination: check the lamp holder, then the globe, then the transformer.
- Stay on the 12V side: only work on the extra low voltage side of the transformer.
- A loose lamp holder is common: it causes heat and a flickering or dead downlight.
- Never open a 240V plug socket: that part is for a licensed electrician only.
Halogen Downlight Not Working? Test It Step by Step
Skefos from Florance Electrical here with another handy electrical tip! We would like to show you how to diagnose which component of a downlight is faulty using a simple process of elimination, and describe each part of a downlight and its function.
If you just need to swap a blown globe, start with our guide on how to replace a halogen downlight globe. This post is for when a new globe does not fix it.
Step 1: Check the Silicone Lead and Lamp Holder
The first component of a halogen downlight that we are going to look at is the silicone lead. This lead is connected to the ELV or extra low voltage side of the transformer and is safe to handle if you have a 12V downlight installed in your home or business. We often find that these silicone lamp holders become loose through standard wear and tear.
This loose connection from the transformer to the globe can cause excessive heat to be emitted and therefore raises the resistance of the electrical circuit. When plugging and unplugging the silicone lead, it should feel tight against the lamp or globe and not fall away from the pins of the globe too easily. If it does, this could indicate a loose connection and may be the cause of the downlight ceasing to function.
It is also a very good idea to perform a visual inspection on the silicone lead and look for signs of discolouration or feel for heat. These two signs are also an indication of a loose connection against the halogen globe, if present.
How to Test the Lead for a Loose Connection
If you don’t feel any resistance and you find that it’s a little bit loose, turn it on from the switch, plug the lead into the globe and move it around to see if the light flickers. If it does, congratulations! You have found the issue with your faulty halogen downlight.
These silicone leads can be purchased from any electrical wholesaler and are relatively inexpensive. They are also easy to replace yourself with a simple screwdriver. Just be sure that you are only working on the ELV / 12V side of the transformer, and if in doubt, call a licensed electrician.
Step 2: Test the Halogen Downlight Transformer
The next component that we will look at is the transformer. If you have a transformer with a lead coming out of it which is plugged into a 413 plug socket, then you will know that you will not need an electrician to replace your downlight, as the 240V live electrical circuit is safely contained within the 413 plug socket and not accessible.
Do not under any circumstances open this plug socket if you are not a licensed electrician, as it is very dangerous and potentially fatal.
If you have a spare 12VAC transformer with a suitable or equivalent amperage to the downlight, simply swapping the transformers is the ideal way to eliminate a faulty transformer without further testing. If the replacement transformer functions, the existing transformer was faulty.
If a 413 plug socket is existing, simply unplug the faulty downlight and plug in the working one as you would with a power point, test and then re-install into the ceiling.
Putting a Halogen Downlight Back in the Ceiling
The two clips either side of the downlight frame pull back towards the centre of the downlight and spring against the gyprock inside the roof cavity once the downlight is pushed up and into the cut-out.
When to Replace the Downlight With LED
If the lead, globe and transformer are all in order and the light still fails, or the fitting is old and discoloured, it is usually more cost effective to upgrade than to keep repairing. Replacement LED downlights use less power and give off less heat. Our electrical fault finding team can trace hardwired faults that you cannot safely test yourself.
Frequently Asked Questions
How do I test a halogen downlight?
Work by elimination. Check the silicone lead for looseness, heat or discolouration, try a known good globe, then swap in a spare transformer of the right amperage. If the light works with the spare, the original part was faulty.
Why does my halogen downlight flicker?
A loose silicone lamp holder is a common cause. Plug the lead into the globe with the power on and move it gently. If the light flickers, the lead has a poor connection and needs replacing.
Can I replace a downlight transformer myself?
Only if it is a plug-in type on a 413 plug socket, where the 240V part is enclosed. If the transformer is hardwired, or you would need to open the plug socket, call a licensed electrician.
How much does it cost to repair a halogen downlight?
Silicone leads are inexpensive from electrical wholesalers. Hardwired transformer work depends on the job. Contact us and we will explain the options and the likely cost before we start.
Downlight Still Dead? Call a Darwin Electrician
If your downlights still don’t work, our licensed electricians can find the fault and fix it. Request a booking or call (08) 8983 3000.